Did you know?

https://www.litter-robot.com/Thank you for upgrading your Litter-Robot to our Wi-Fi-enabled Connect Base. We're confident that you will appreciate the ease o...Community for all things Litter-Robot. Post your experiences, tips, tricks, and hacks. ... For years now I've been getting "bonnet removed" errors that I can sometimes resolve with a remote power cycle. Other times I have to physically go to the unit and futz with the bonnet, then it starts to work again.Apr 27, 2022 ... ... robot in the center. I believe these are all you need to take out to remove base, just keep track of what you've removed and from where. If ...The Litter-Robot litter sifting system requires clumping litter to work properly. We recommend a high quality clay clumping litter. Litter beads and crystals that are small enough to pass through the screen will also work (periodic changing of this type of litter is required). • If possible, place the Litter-Robot in the same location as theThe 2 back bonnet tabs are not fully locked in The black key on the back of the globe is not locked in place There is debris underneath the globe - remove the bonnet and globe and vacuum it out You need to clean your bonnet connectors, which are the silver strips on both the bonnet and the base. Clean them with a dry magic eraserWith two cats, the constant cleaning of the litter was becoming a hassle. However, the litter robot 4 has completely changed the game for us. Not only has it saved us time and effort, but it has also reduced our litter usage by a whopping 90%. It's definitely worth the investment!“It’s very easy to get intimidated,” says Hamayal Choudhry, the robotics engineer who co-created the smartARM, a robotic hand prosthetic that uses a camera to analyze and manipulat...Remove the screw from the center of the black key on the back of the globe. Once the key is removed, you can easily pull the shield out from the entrance of the globe. If you decide to remove the shield, please let us know and we will send you a key-hole plug for the back of the globe. You can see the video on how to remove it here. 4. BonnetLitter-Robot 4 is equipped with brush-type seal strips that sit along the lower globe, bezel, and waste port. ... Unlatch the center tab on the bonnet from the catch clip on the unit frame behind the robot. Set the bonnet aside. Remove any accessories (if installed). Remove the globe: Grab the black handle located on top of the globe, lift the ...Keep in mind that the LR is measuring the weight of BOTH the waste in the drawer + the litter in the globe. Once that max is reached, it generally stops upside down in the middle of a cycle. I personally never add litter unless I change the drawer, which I do 2x a week whether it needs it or not for odor control.To reset the unit, follow these steps: [Turn off and unplug the unit prior to this troubleshooting] Customer Service Code: 3031. Remove the bonnet and set it aside. Remove the globe and set it aside, but be careful not to let it roll. Inspect the exterior, top portion of the base where the globe usually rests.Ensure all (3) clips are unhooked, then pull the Globe liner retainer forward to expose access behind the liner. 6. Pull the Globe liner up and replace the weight in the liner pocket as shown. 7. Reseat the front of the liner lip on the Globe. 8. Push the "fangs" of the liner retainer clips to the inside of the Globe. 9.Remove the bonnet by pressing the latches on both sides of the bonnet. Lift while rotating it backwards. ... Litter-Robot ships with a waste drawer liner installed. These liners are made specifically for any Litter-Robot model, but an 8-13 gallon (30-49L) trash bag will also work. Clear bags work best.I was having this issue too.I saw somewhere (think it may have been the Litter Robot website) to take off the bonnet, push the two side tabs as far out to the side (as close to 90°) as you can (I did this for like a minute and a half), then put the bonnet back on back left tab first, then back right, the left side tab and then right.

Get started by following the steps below. If possible, place Litter-Robot in the same location as the old litter box (at least during transition). Make sure the unit is on a firm, level surface in a cool, dry location. Locate the unit near a power outlet. Ensure the unit isn’t pushed against a wall or into a corner (must not be touching any ...The Robots Channel contains articles related to the workings of robots and robot components. Learn about robots on the HowStuffWorks Robots Channel. Advertisement Robotics is the s...Cleaning the sensors. With the globe, bonnet, and drawer removed, lean the unit backward so that you can look into the holes on the bezel to see each sensor. Using a clean, dry cotton swab, carefully clean the surface of each sensor to remove any dust. It is important to note that it will be very difficult to see any dust, specifically on the ...Explore Litter-Robot 3. Accessories. Bundles. How it Works. Features & Benefits. The App. Got questions or issues? Contact Litter-Robot Support today. We're dedicated to ensuring a seamless experience for you & your pet.

Flip the bonnet over to expose the underside of the bonnet where the circuit board is located. Using a Phillips-head screwdriver, remove the screw holding the circuit board bracket. Remove the circuit board from the bracket. Unplug the circuit board from the wire harness. Plug the wire harness into the replacement circuit board.Why does my Litter-Robot stop mid-cycle? If your Litter-Robot 3 stops mid-cycle, check out this helpful troubleshooting video to help remedy the problem. We'...If the bonnet is removed, the yellow light should blink once per second. Do you get an error on the App. saying this while the yellow light is blinking twice per second? What happens when you press ……

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Litter-Robot 4 features a Bonnet that cov. Possible cause: The Litter-Robot 3 is equipped with a cat sensor that detects when a cat ente.