Did you know?

Eaton Customer Quality Group at (616) 342-3000. 5. If the tower mounted shift lever is used, it the OEM's responsibility to ensure the tower assembly is rigidly mounted. As a guideline, a minimum floor thickness in the mounting area of 0.250" for alumimum (0.125" for steel) is recommended. Shift Lever Recommenda-tionsAn update on my problems with the 2005 junk Eaton 10 spd. Two long trips and the same event sequence of events of quick reshifts in and out of 10th after about two hours on the road, then more frequent 10th gear studders, then speedo drops to 0, fault light in 10th and then eventually total lockup stuck in 10th. 4 times, like clock work, if locked in 10th after 4 hours of running.Volvo VNL , Cummins ISX, Eaton Fuller 10 Speed Autoshift. I was having an issue sometimes with the tranny downshifting from 7 to 6. So today I replaced the xy shifter and the wiring harness for the xy … read moreFor the price of trying to diagnose the problem by throwing a xy shifter, new clutch, new tcm, labor etc. you're already invested half towards a manual transmission conversion. boneebone , Oct 18, 2017Eaton Fuller transmission has shifting problems.Issues thus far have been: wire going to the x-y sifter corroded internally, power module failed, o-rings in the splitter box needed replacing. ... I have a three pedal Eaton-Fuller, auto shift coupled to a 12.7 DD-60 430 …Eaton Reman XY Shifter S2745R. Be the first to write a review. governmenttransitsurplus(10491) 100% positive feedback; Price: Free shipping. ... OEM Eaton Fuller 13 Speed Transmission Shift Knob Medallion Pattern 5586113. 5.0 out of 5 stars based on 10 product ratings (10) $18.50 NewTo use the guideline, 1) Locate the transmission problem in the boxes below. 2) Hover over the box to see the possible problem and take note of the numbers next to the possible cause. 3) Refer to the list below and locate the corresponding number listed next to the problem.to shift (see Note *). † System holds current gear unless otherwise prompted by using up / down-shift buttons, except for the “Transmission Override” condi-tions noted below. Note: Multiple gear upshifts and downshifts may be allowed when the shift buttons are pushed multiple times (Each button push equals one gear change request). movement of the XY Shift finger. This fault will set when the Electric Shifter fails to select the proper rail. − FMI 5, 6 - This fault is set when the condition is detected for at least 0.5 seconds and the TECU attempts to move the XY shift finger. FMI 5 is open or shorted to ground, FMI 6 is shorted to power.Position X-Y Shifter on the Shift Bar Housing. Using a 9/16” socket, install mounting cap screws and tighten in a cross pattern as follows: Tighten to 30–35 lb-ft (45–60 N•m).The Fuller Advantage X-Y Shifter is equipped with a Gear Position Sensor. The X-Y Gear Position Sensor reports fore-and-aft movement of the Shift Finger to the Transmission Electronic Control Unit (TECU) as a voltage signal. The X-Y Gear Position Sensor is connected to the TECU via the Transmission Harness. You may need to replace your XY shifters, as well as the sensors with better ones to resolve the problem once and for all. But if the XY shifters and sensors are not causing these problems, and yet you …movement of the XY Shift finger. This fault will set when the Electric Shifter fails to select the proper rail. − FMI 5, 6 - This fault is set when the condition is detected for at least 0.5 seconds and the TECU attempts to move the XY shift finger. FMI 5 is open or shorted to ground, FMI 6 is shorted to power.Position X-Y Shifter on the Shift Bar Housing. Using a 9/16” socket, install mounting cap screws and tighten in a cross pattern as follows: Tighten to 30–35 lb-ft (45–60 N•m).

problems. Upshift / Downshift Buttons Used in the MANUAL mode to select upshifts and downshifts and to change start gear, if available. R - Reverse N - Neutral D - Drive MANUAL LOW - Upshift - Downshift SERVICE SHIFT MANUAL EATON FULLER TRANSMISSIONS LOW D N R Button not used Service Indicator!10 k-7061 shift lever hsg kit 241075 ,4302711 ,a - 6439 1 aluminum housing medium - lever height 3-1/8" 11 k-7056 shift lever hsg kit 4302654 1 cast iron housing low - lever height 2-7/8" 11 k-7065 shift lever hsg kit 4302704 ,4302711 ,a - 6448 1 aluminum housing low - lever height 2-7/8" 12 22383 stub, shift lever 3-1/8"For Sale: $29,0002017 Kenworth T680 with 791,000 miles. I am the second owner and have my maintenance records. Truck belonged to, and was maintained by, CRANE Transport prior to my purchase in March 2021. EATON XY shifter was replaced a year ago. No issues with DEF system since I have owned the ...Electrical and Industrial | Power management solutions | EatonElectrical and Industrial | Power management solutions | Eaton

7 Item Current Part Description Replaced Part Qty. Notes Kits/Assys Where Needed 2 5568511 -O- RING 1 K-2918,S-2501,S-2913,S-2956 3 K-2918 OIL SEAL KIT 4302322 4302323 1 "FOR MAGNETIC COVER" K-3519,K-3522Eaton Transmissions TRSM0080 FS-4106A FS-4206B FSO-4206B FS-5206A FS-5206B FS-5206F FSO-5206B October 2009. ... This symbol is used throughout th is manual to call attention to procedures where carelessness or failure ... Removal of the gear shift remote control housing assembly is included in the detailed instructions; how-Service Bulletin – Process Page 1 of 2 Subject: Shift Complaint After Installing New XY Shifter – Gen 3 Product Document Number: TAIB-0858 Date: September 24, 2015 Issue Description: Transmission fails to engage a start gear or has shifting related issues immediately after the XY shifter has been replaced and calibrated.…

Reader Q&A - also see RECOMMENDED ARTICLES & FAQs. Fault Code 73 Troubleshooting · Key off. · Remove the . Possible cause: i have 2016 International Pro-star with Eaton Ultra-shift 16 speed. all in sudden it .